二维层状Ni/β-Ni(OH)2纳米复合材料的制备及其摩擦学性能研究

采用水热反应制备出β-Ni(OH)2,然后通过水热还原得到Ni/β-Ni(OH)2纳米复合粉体材料,采用X射线衍射仪(XRD)和扫描电子显微镜(SEM)对复合材料的相结构、成分及形貌进行表征分析。采用四球摩擦磨损试验机评价制备的Ni/β-Ni(OH)2作为润滑油添加剂的摩擦学性能,基础油为PAO6。摩擦试验后,采用SEM分析典型试验钢球磨斑的表面形貌,利用能谱仪(EDS)研究磨斑表面化学元素的组成,探讨Ni/β-Ni(OH)2纳米复合润滑添加剂的减摩抗磨机制。结果表明:Ni/β-Ni(OH)2纳米复合材料作为润滑添加剂具有极好的减摩抗磨性能,显著优于基础油PAO6和未负载纳米Ni的二维β-Ni(OH)2层状材料;与基础油相比,添加0.1%质量分数Ni/β-Ni(OH)2添加剂的油样的摩擦因数和磨斑直径分别降低了17.6%和41.5%;Ni/β-Ni(OH)2纳米复合粉体综合了纳米Ni及层状β-Ni(OH)2两部分结构特性,在摩擦过程中,复合材料中的纳米金属粒子Ni与层状结构材料β-Ni(OH)2能够相互增强起到协同润滑作用。     

双馈风机经VSC-HVDC接入弱受端系统运行特性分析

基于电压源换流器的高压直流输电(VSC-HVDC)是远距离风电并网的理想方案,同时可用于联接弱受端系统,但双馈风机经VSC-HVDC能够馈入多弱的受端系统仍待深入研究,有必要提出基于短路比的指标来衡量所能接入的受端系统。对此,基于定功率控制下VSC的稳定运行约束,分析系统稳态的临界运行点,总结出临界短路比的求解步骤。在此基础上,结合双馈风机的控制方程,详细讨论了风电场出力、弱交流系统等效阻抗和临界短路比的关系。仿真分析发现,受双馈风机无功特性的影响,接入受端系统的临界短路比未能达到理论值,引入基于无功补偿的有效短路比作为受端系统的强弱判断指标,使得所提临界短路比求解方法在此工况下依然成立。     

Microstructural and microwave dielectric properties of LZT (Li2ZnTi3O8) ceramics sintered in presence of bismuth borate glass for LTCC applications

In the present research, the Li₂ZnTi₃O₈(LZT) ceramics were synthesized throughout solid-state ceramic processing, then mixed with bismuth borate (BiBO) glass prepared based on conventional melt quenching method. Wetting behavior of BiBO glass on the LZT ceramic substrate was monitored by hot stage microscopy. Afterward, dielectric LZT ceramics containing different amounts of BiBO glass (0.25–6 wt%) were sintered at various temperatures. X-ray diffraction and electron back scatter diffraction examinations revealed the presence of two crystalline phases of Li₂ZnTi₃O₈ and Bi₂Ti₂O₇. The maximum value of relative density (above 95%) was obtained in the case of specimens contained more than 5 wt% glass. The microwave dielectric properties of the finally sintered BiBO glass containing LZT ceramics were as follows: dielectric constant (ε_r) = 21.44–25.09, quality factor (Q × f) = 10839–54708 GHz and temperature coefficient of resonant frequency (τ_f) = (? 15.58) ? (? 12.86)ppm/°C.     

Porous ceramics with tailored pore size and morphology as substrates for coral larval settlement

The growing demand for stony corals as ornamental aquarium animals requires defined aquacultural breeding strategies. For the sexual propagation of corals, material substrates are needed, that attract larvae and support their settlement and development. In this study, five types of highly porous ceramic materials were developed following the example of coral skeleton. The applicability of these settlement substrates was tested using larvae of the stony coral Pocillopora damicornis. Partial sintering of pressed clay pellets, freeze casting of clay and alumina-mullite based slurries and direct foaming of high alkane phase emulsified suspensions (HAPES) using alumina were employed. By the addition of mm-sized spherical polystyrene beads as sacrificial templates during freeze casting (alumina-mullite), superficial pores in the size of the larvae were created. The inorganic substrates featured open porosities between 35% (pressed clay) and 83% (foamed alumina), pore sizes ranging from nm to mm-scale and pore morphologies dominated by interparticle porosity (pressed), lamellar pores (freeze casting) and cellular pore types (direct foaming). The ceramic substrates were incubated in artificial sea water for 3 months to induce necessary biofilm formation and algae growth. Afterwards, individual substrates were exposed to 5 coral larvae, and their settlement behavior was monitored over 14 days. At the end of this period, all ceramic materials were successfully accepted as settlement substrates, with a mean settlement rate of 46.2%, and no significant differences between the substrate types. On samples with large surface superficial pores, a significantly reduced survival of settled larvae (79%) compared to the other porous materials (93–98%) was determined, suggesting a non-ideal surface topography. While alumina foam samples (HAPES) exhibit the most promising results in terms of settlement and survival of larvae, clay-based substrates provide a more economic solution for the sexual propagation of corals in aquaculture.     

Impact performances of steel tube-confined recycled aggregate concrete (STCRAC) after exposure to elevated temperatures

The impact behaviours of steel tube-confined recycled aggregate concrete (STCRAC) following exposure to elevated temperatures of 20 °C, 200 °C, 500 °C and 700 °C were experimentally investigated using a 100 mm-diameter split Hopkinson pressure bar (SHPB). The recycled coarse aggregate (RCA) replacement ratios were set as 0, 50% and 100%. The effect of RCA replacement ratio and exposure temperature on the impact properties of STCRAC were analysed in terms of failure modes, stress-strain time history curve and dynamic increase factor (DIF). The results show that the fire-damaged STCRAC can maintain its integrity during impact load. However, there were evident degradations in the dynamic behaviour of STCRAC after exposure to high temperatures of 500 °C and 700 °C. The ultimate impact strength, impact secant modulus and residual impact strength of STCRAC obviously decreased because of the damage due to high temperature exposure. But the degradations of both the ultimate impact strength and impact secant modulus of STCRAC under impact loading were less severe than those under quasi-static loading. The remaining strength factor and the DIF tended to increase with the raise of the elevated temperatures. Overall, during the impact loading, the fire-deteriorated STCRAC exhibited excellent impact behaviour.     

粒径对庚烷液雾爆炸场影响的数值模拟

为了研究液雾索特直径(D_(32))对爆炸参数的影响,以庚烷为对象,控制液雾总浓度不变(80 g·m~(-3)),改变液雾粒径,数值模拟了爆炸容器内庚烷(C_7H_(16))液雾粒径对爆炸参数的影响。结果表明:庚烷液雾场索特直径D_(32)为0~18.1μm时,最大爆炸压力p_(max)随D_(32)增加逐渐减小,最大值为1.01 MPa,最小值为0.9015 MPa。最大爆炸压力上升速率随D_(32)增大整体呈下降趋势,在0处达到最大值0.37571 MPa·ms~(-1),在18.1μm处达到最小值0.18439 MPa·ms~(-1),但在6.81~12μm发生反向突变,在10.1μm处达到极大值0.34217 MPa·ms~(-1),随后恢复下降趋势。液雾的径向火焰传播速度在径向距离15 cm附近突然增加,在16 cm之后剧烈下降。最大火焰速度随液雾场D_(32)不同而变化,D_(32)=10.1,12.9,18.1,6.81,0μm条件下液雾场的最大火焰速度依次降低,最大值为5.714 m·s~(-1),其后依次为1.737,1.36,1.34,1.27 m·s~(-1)。     

Hydrogen refuelling stations in the Netherlands: An intercomparison of quantitative risk assessments used for permitting

As of 2003, 15 hydrogen refuelling stations (HRSs) have been deployed in the Netherlands. To become established, the HRS has to go through a permitting procedure. An important document of the permitting dossier is the quantitative risk assessment (QRA) as it assesses the risks of the HRS associated to people and buildings in the vicinity of the HRS. In the Netherlands, a generic prescribed approach exists on how to perform a QRA, however specific guidelines for HRSs do not exist. An intercomparison among the QRAs of permitted HRSs has revealed significant inconsistencies on various aspects of the QRA: namely the inclusion of HRS sub-systems and components, the HRS sub-system and component considerations as predefined components, the application of failure scenarios, the determination of failure frequencies, the application of input parameters, the consideration of preventive and mitigation measures as well as information provided regarding the HRS surroundings and the societal risk. It is therefore recommended to develop specific QRA guidelines for HRSs.     

Unity direct chain with feedback series impedance based innovative negative group delay circuit

An innovative negative group delay (NGD) circuit theory on unity direct chain (UDC) topology is developed in this paper. The NGD UDC cells are based on the operational amplifier adder with feedback series impedance. Innovative topologies of high-pass NGD UDC cell composed of RL-series network, all-pass RC-parallel network and low-pass RC-series network are identified. It is a first time that all-pass NGD original topologies are defined. NGD analyses and synthesis methods of each NGD UDC cells are provided. The UDC cell based NGD functions are validated with SPICE simulations. The proofs-of-concept (POC) of UDCs behave as all-pass and low-pass NGD functions with group delay equal to −1 ms at very low frequencies. The low-pass NGD cut-off frequency is 424 Hz. The high pass NGD circuit generates −1 µs at the optimal NGD frequency of about 5.15 kHz. Further analysis of the operational amplifier gain and bandwidth effects is performed. The operational amplifier gain affects significantly the NGD level and bandwidth for the all considered UDC cells. Nevertheless, only the RC-parallel feedback based UDC cell is particularly sensitive to the operational bandwidth.     

Smart utilization of renewable energy sources in a microgrid system integrated with plug‐in hybrid electric vehicles

Mass roll‐out of plug‐in hybrid electric vehicles (PHEVs) and significant penetration of renewable energy sources in distribution system play a major role in delivering low carbon environment. However, placing and utilizing these units randomly result in overloading, increased power loss, and reduced voltage profile. This paper responds to these technical challenges by using a strategic placement method for locating the distributed generation (DG) and the charging station (CS) of PHEVs in a multi‐zone distribution system. For simultaneously scheduling of these units in each zone, the smart energy management framework is proposed in this paper. Apart from usual energy management constraints, this paper also incorporates the real‐time constraints involving the capacity of PHEV batteries, the mobility pattern, and the power level of the charging infrastructure. The simulation studies are carried out for each hour of a day. To cope with this time constraint execution, particle swarm optimization algorithm‐based approach is used. The proposed framework is tested in IEEE 33 and IEEE 69 bus radial distribution system. The obtained results imply that the presented energy management framework provides maximum profits for the vehicle owner, and meanwhile it fulfills preferences of the user in each zone simultaneously.